Product Description
SURPRISING POWER IN A COMPACT PACKAGE
The UPA loudspeakers provide high power output, low distortion, and consistent polar response in a compact, vented two-way enclosure for exceptional fidelity and extended high-frequency performance.
EXCEPTIONAL MEYER SOUND TECHNOLOGY
The Constant-Q horn affords uniform response throughout the coverage area, be it wide (UPA-1P) or narrow (UPA-2P). In addition, extraordinarily flat amplitude and phase response allow for tonal accuracy and precise imaging.
MAKES DESIGNING A BREEZE
Predictable array performance ensures system design flexibility. Optional rigging frame, mounting yoke and pole mount adaptors allow fast, flexible installation and easy aiming.
UPA specifications
Acoustical
Operating Frequency Range: 60 Hz – 18 kHz
Frequency Response: 80 Hz – 17 kHz ±4 dB
Phase Response: 600 Hz – 16 kHz ±35°
Maximum Peak SPL: 133 dB
Dynamic Range: >110 dB
Coverage
1P- Horizontal: 100°
Vertical: 40°
2P- Horizontal: 45°
Vertical: 45°
Crossover
1P:1200 Hz
2P:1000Hz
Transducers
Low Frequency:One 12″ cone driver
Nominal impedance: 2 Ω Voice coil size: 3″
Power-handling capability: 400 W (AES)5\
High Frequency:One 3″ compression driver
Nominal impedance: 16 Ω Voice coil size: 3″
Diaphragm size: 3″
Exit size: 1.4″ throat
Power-handling capability: 100 W (AES)5
Audio Input
Type:Differential, electronically balanced
Maximum Common Mode Range:±15 V DC, clamped to earth for voltage transient protection
Connectors: Female XLR input with male XLR loop output or VEAM all-in-one
(integrates AC, audio and network)
Input Impedance: 10 kΩ differential between pins 2 and 3
Wiring: Pin 1: Chassis/earth through 220 kΩ, 1000 pF, 15 V clamp network to
provide virtual ground lift at audio frequencies
Pin 2: Signal +
Pin 3: Signal – (optional polarity reversal switch)6
Case: Earth ground and chassis
DC Blocking: Differential DC blocking up to maximum common mode voltage
CMRR: >50 dB, typically 80 dB (50 Hz – 500 Hz)
RF Filter: Common mode: 425 kHz; Differential mode: 142 kHz
TIM Filter: <80 kHz, integral to signal processing
Nominal Input Sensitivity: 0 dBV (1 V rms, 1.4 V pk) continuous average is typically the onset of
limiting for pink noise and music
Input Level:Audio source must be capable of producing a minimum of +20 dBV (10
V rms, 14 V pk) into 600 Ω to produce maximum peak SPL over
the operating bandwidth of the loudspeaker
Amplifier
Type: Two-channel complementary MOSFET output stages (class AB/bridged)
Output Power: 550 W total
THD, IM, TIM: <.02 %
Load Capacity: 2 Ω low channel, 16 Ω high channel
Cooling: Convection; 24 V DC output for optional external fan
AC Power
Connector: PowerCon or VEAM
Voltage Selection: Automatic, continuous range from 90 V AC to 265 V AC
Safety Agency Rated Operating Range: 100 V AC – 240 V AC; 50/60 Hz
Turn-on and Turn-off Points: 90 V AC on, no turn-off, only fuse-protect above 265 V AC
Current Draw: Idle Current: 0.25 A rms (115 V AC); 0.13 A rms (230 V AC); 0.3 A rms (100 V AC)
Max Long-Term Continuous Current (>10 sec): 2.8 A rms (115 V AC); 1.4 A rms (230 V AC); 3.2 A rms (100 V AC)
Burst Current (<1 sec): 3.2 A rms (115 V AC); 1.6 A rms (230 V AC); 3.7 A rms (100 V AC)
Ultimate Short-Term Peak Current Draw: 5.0 A pk (115 V AC); 2.5 A pk (230 V AC); 5.8 A pk (100 V AC)
Inrush Current: <9 A pk (115 V AC and 230 V AC)
RMS Network (Optional)
Equipped for two-conductor, twisted-pair network, reporting
amplifier operating parameters to system operator’s host computer.